VEVOR 150W 165 CFM Solder Fume Extractor, Smoke Absorber, 3-Stage Filters 3 Speed with Two Hoses for Soldering, Laser Engraving and DIY Welding

𝗣𝗿𝗼𝗱𝘂𝗰𝘁 𝗗𝗲𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻

· Professional Purification

The exhaust and dust pass through 3 stage filters of the fume, an impressive 99.91% of the tiniest particles in the air are absorbed. When the filter elements are blocked, the automatic filter block alarm will sound to remind you.

· 3-Stage Speed

One button controls 3 levels of speed. You can adjust the flow speed from weak to strong according to the environment.

· Low Noise Motor

Boasting a 150W DC motor that can reach a max airflow speed of 280 m3/h, this welding fume extractor has a strong suction power while maintaining a noise below 63.

· Long Flexible Hoses

Our smoke extractor comes with two 1.2 m (47.2inch) 360° extractor tubes, which can easily stretch, bend and rotate to the angle you need.

· Easy Movement

The dimension of the fume extractor is 11 x 11 x 16.9 inches. It's about the size of A4 paper. You can put it on the table or under the table. Two 360 degree casters with 2 lockable wheels make it move freely in your work area.

· Wide Application

Suitable for bench top soldering and electronic rework applications as well as laser, handheld machining operations. Widely used in physiotherapy, laser engraving, chemical experiment, home and office.

𝗦𝗽𝗲𝗰𝗶𝗳𝗶𝗰𝗮𝘁𝗶𝗼𝗻𝘀

Model: FL250

Filtering Effect: 0.3μm 99.91%

Systemic Flow: 165 CFM

Max Rotation Speed: 4500 RPM

Noise: 63 db

Power: 150 W

Fliteration Expansion Area: 2.1m2

Length of Smoke Tube: 1.2 m/47.2 inch

Product Dimension: 11 x 11 x 16.9 inch

𝗣𝗮𝗰𝗸𝗮𝗴𝗲 𝗖𝗼𝗻𝘁𝗲𝗻𝘁

1 x Fume Extractor

2 x Smoking Pipe

2 x Smoking Cover

5 x Primary Filter Cotton

1 x HEPA Filter

1 x Activated Carbon Filter

1x Power Cord

1 x Manual

· 99.91% Purification Rate: The 150W DC motor of the fume extractor creates a powerful 165 CFM airflow to exhaust and purify the air. After using, the smoke purification rate is as high as 99.91%, allowing you to breathe fresh air again.

· 3-Stage Filters: The solder fume extractor has 3 stage filters for high-quality filtration. A cotton filter, central HEPA filter, and an activated carbon filter absorb all smoke, dust, and harmful gases at work. The filter boasts of pleated design, with an expansion area of 2.1m2, significantly increasing filtration effectiveness.

· 3 Adjustable Speeds: The speed of our welding fume extractor can be adjusted according to your work needs. Three stages speed from strong to weak can meet different working requirements. Only when you has a comfortable working environment, you can improve work efficiency.

· Low Noise Motor: The powerful 150W DC brushless motor of the FL-250 fume extractor creates a max rotation speed of 4500 RPM. In addition, our engine features low noise. The sound can be lower than 63 db, which quietly gives you a fresh environment.

· Compact & Flexible: Our smoke extractor is 11 x 11 x 16.9 inches, like an A4 paper size, which is suitable for small solder stations and home DIY. Our metal latches very tightly closed the main filter bulk, completely sealed to prevent any leak. There are four wheels. Among them, two are lockable, ensuring flexible and easy movement.